| << Vorige - Volgende >> |
FANLESS BOORDPC - 12Volt - Krachtig & zeer EnergiezuinigDè 2023 versie boordPC voor grote reizen. Fanless. Veel uitvoeringen. De gunstigst geprijsde ! +NANO Artikelcode: SUN-EM317
|
|||||||||||||||||||||||||||||||
|
Artikelnummer: SUN-EM317
Uitvoering met de Intel Pentium Silver N6005 processor
SPECIFICATIONS
[1] Optional LTE support
Optional Accessory “WWN03" which consists of an adapter card, two antennas plus 20 cm antenna cables. The WWN03 adapter card occupies the 2.5" drive bay, so that no more 2.5" SATA device can be installed. The 3G/LTE card must have M.2-3042 Key B format with MHF IV (I-PEX4) connectors for the antenna. In addition, it supports one Nano-SIM card (Mini and Micro format is not supported). The required 3G/LTE card and SIM card are not included in WWN03. [2] How to convert DisplayPort into HDMI/DVI The DisplayPort output can be converted to HDMI or DVI by an additional, passive adapter cable. For example: DELOCK 82590: 1 m, DisplayPort (male, 20p) to HDMI-A (male, 19p) DELOCK 82435: 5 m, DisplayPort (male, 20p) to DVI-D (male, 24p) The integrated graphics automatically detects the connected display and puts out the appropriate electric signal - either through DisplayPort (without an adapter) or HDMI/DVI (with an adapter). However, a monitor with a DisplayPort connector cannot be connected to the HDMI port with a simple, passive adapter. [3] Power-on-after-power-fail The BIOS setup provides a "Power-on-after-power-fail" function that can be found under "Power Management Configuration". As the name indicates, this function determines the PC's behaviour after power failure: (1) unconditional power-on, (2) restore former status or (3) keep system turned off. As a matter of the nature of this function, it may fail after short power failures. SUN-DL206 also comes with a hardware-based solution. By removing Jumper JP1 (on the mainboard behind the D-Sub/VGA port) the system will start unconditionally once power is supplied. [4] Serial Ports This PC features two serial RS232 ports with 9-pin D-Sub connectors on the back panel. The left COM port (COM1) can also be configured as RS422 and RS485 in the BIOS setup. Pin 9 of the D-Sub COM-Port is a multi-functional signal. Based on the Jumper JP2 configuration on the mainboard, it can be configured as Ring Indicator (RI) or external power supply with a voltage level of either 5 V or 12 V. Each COM port can be configured separately. The maximum current is 500 mA per connector. [5] TPM Function This product features Firmware-TPM (fTPM) v2.0. Besides this, it is prepared for a hardware TPM chip which can be fitted by factory on request if required. Artikelnummer: SunPc-EM317
Uitvoering met de Intel Celeron N4505 processor
Fanless and silent
Completely fanless, virtually noiseless
Passive cooling through convective heat transfer
Perfect to be used in noise-sensitive environments
Fanless means less dust and thus virtually no maintenance required
24/7 Nonstop Operation
This device is approved for 24/7 permanent operation.
Requirements:
- Free air circulation around the PC must be guaranteed.
- Ventilation holes must be kept clear.
- Any installed disk must also be approved for permanent
operation by its manufacturer
Chassis
Slim PC with black chassis made of steel
Dimensions: 190 x 165 x 43 mm (LWH) = 1.35-litre
Weight: 0.8 kg net and 1.95 kg gross
Two holes for Kensington Lock and numerous
threaded holes (M3) at both sides of the chassis
Operation Position
1) Horizontal
2) Vertical with mounted feet.
These feet can be purchased as optional accessory PS02.
3) Vertical (e.g. VESA-mounted behind an appropriate monitor)
In vertical position, the front USB ports should point upward.
Ventilation holes must not be blocked to ensure sufficient cooling.
Operation System
This system comes without operating system.
It is compatible with
- Windows 10 (64-bit)
- Windows 11 (64-bit)
- Linux (64-bit)
Processor
Intel® Celeron® Processor N4505, Dual Core
CPU clock frequency: 2.0 GHz, max. Turbo frequency: 2.9 GHz
Code name: "Jasper Lake"
10 nm structure, FCBGA1338 package (soldered)
CPU cores / Threads: 2 / 2
L2 Cache: 4 MB
Thermal Design Power (TDP): 10 W
Supports x86-64, AES-NI, VT-x (EPT), VT-d, SSE4.2, AES
System-on-Chip processor (SoC) with integrated graphics processor, no chipset required
Integrated Graphics
The Graphics Processing Unit (GPU) is integrated in the processor
Intel® UHD Graphics (11th Gen), GPU frequency: 450~750 MHz
Supports DirectX 12, OpenGL 4.5, OpenCL 1.2, Intel Quick Sync Video, Intel Clear Video (HD)
Execution Units (EU): 16
Triple Display Support via three video outputs:
- HDMI 2.0b: max. 4096 x 2160 @ 60 Hz
- DisplayPort 1.4a: max. 4096 x 2160 @ 60 Hz
- D-Sub/VGA: max. 1920 x 1200 resolution @ 60 Hz
Supports two digital displays and one analog display simultaneously.
The D-Sub/VGA connector does not support the Hot Plug feature.
UEFI Firmware
16 MB Flash ROM with AMI's Aptio UEFI BIOS Firmware
Based on the Unified Extensible Firmware Interface (UEFI)
Supports Power-fail-resume / AC power-on state / always-on / always-off [3]
Supports Wake-on-LAN (WOL) from S3, S4, S5 ACPI states
Supports boot up from external flash memory cards
With embedded Firmware TPM v2.0 (fTPM) [5]
CMOS battery (type CR2032)
Memory Support
2x SO-DIMM slots with 260 pins
Supports DDR4-2933 (PC4-23466U) SDRAM at 1.2V
Supports Dual Channel mode
Supports max. 16 GB per DIMM
Maximum total size: 16 GB (either 1x 16 GB or 2x 8 GB)
Supports two unbuffered DIMM modules (no ECC)
2.5" Bay for Hard disk drive/SSD
Supports one drive in 6.35 cm / 2.5" format (hard disk or SSD)
Serial ATA III Interface with up to 600 MB/s transfer speed
Max. height 12.5 mm
Pre-installed SATA cable (data / power)
Supports Unified Extensible Firmware Interface (UEFI)
M.2 expansion slot for SSD card
M.2 2280 BM slot
Interfaces: PCI-Express Gen. 3.0 X2 and SATA v3.0 (max. 6 Gbit/s)
Supports M.2 cards with a width of 22 mm
and a length of 42, 60 or 80 mm (type 2242, 2260, 2280)
Supports SATA SSDs (BM-Key) or NVMe PCIe SSDs (M-Key)
M.2-2230E slot for WLAN cards
Interfaces: PCI-Express Gen. 2.0 X1 und USB 2.0
Supports M.2 cards with a width of 22 mm and a length of 30 mm (type 2230)
Supports WLAN expansion cards (optional Shuttle accessory: WLN-M / -M1)
Integrated Audio
Realtek ALC897 / ALC662 / ALC888S Audio Codec
Two analog audio connectors (3.5 mm):
1) Line out (head-phones)
2) Microphone input
Digital multi-channel audio output: via HDMI and DisplayPort
Card Reader
Integrated card reader
supports standard SD, SDHC and SDXC memory flash cards
Controller: Genesys GL9750 SD Host Controller
Wired Network
RJ45 connector supports LAN at 100/1000/2500 Mbit/s.
Intel i225 Ethernet Controller with MAC, PHY and PCIe interface
Supports Wake-on-LAN
LEDs and Buttons
Power button
Power LED (blue)
HDD LED (yellow)
Front Panel Connectors
2x USB 3.2 Gen 2 Type A (red)
SD card reader
Audio line-out (headphones)
Microphone input
Back Panel Connectors
HDMI 2.0b digital video and audio output
DisplayPort 1.4a digital video and audio output
D-Sub/ VGA analog video output (15-pin) - no hot plug
2x USB 3.2 Gen 1 Type A (blue)
2x USB 2.0 Type A
Network 2.5 Gbps (LAN, RJ45)
2x RS232 serial port, 9-pin D-Sub (support of an auxiliary voltage of 5/12 V,
the left port is switchable to RS422 / RS485) [4]
DC input for the external power adapter
4-pin connector (2.54 mm pitch) supports
- external power-on button
- Clear CMOS function
- +5V DC voltage for external components
2x perforation for optional Wireless LAN antennas
Other Onboard Connectors
Connectors COM1/COM2 for serial ports (occupied)
Jumper JP2 for power-on-after-power-fail (hardware solution) [3]
USB 2.0 header (4-pin) required for WWN03 accessory
Power Supply
External 40 W AC/DC power adapter (fanless)
AC Input: 100 ~ 240 V AC, 50 ~ 60 Hz
DC Output: 19 V / 2.1 A
Automatic AC voltage adjust
Dimensions: ca. 95 x 42 x 29 mm (LWH)
DC cable length: ca. 170 cm
AC cable length: ca. 170 cm (with 2-pin Europlug)
DC Input connector
DC Connector: 5.5 / 2.5 mm (outer/inner diameter)
The DC-input of the computer supports an external power source
with either 12 V ±5% (max. 3.33 A) or 19 V ±5% (max. 2.1 A).
Supplied Accessories
Multi-language user guide (EN, DE, FR, ES, JP, KR, SC, TC)
VESA mount for 75 / 100 mm standard (two metal brackets)
Four screws M3 x 5 mm (screws together VESA mount and PC)
Four screws M4 x 10 mm (to affix VESA mount on the PC)
Four screws M3 x 4 mm (to mount a 2.5" storage into the bay)
Two screws M3 x 5 mm (to mount some M.2 cards)
Driver DVD (Windows 64-bit)
External 40 W power adapter with power cord (Europlug)
Optional Accessories:
- PS02: optional stand for vertical operation
- CXP01: adapter cable for external power button
- PRM01: 2U rack-mount front plate for two Shuttle XPC slim PCs
- DIR01: DIN-Rail mounting kit
- WLN-M (802.11ac/Wifi 5) and WLN-M1 (802.11ax/Wifi 6): WLAN module in M.2-2230 format with two external antennas supports WLAN and Bluetooth.
- WWN03: LTE kit with adapter card, 2 antennas and antenna cables. Supports one M.2 LTE module and one nano SIM card [1]
Environmental Specifications
Operating temperature range: 0 ~ 40 °C
Relative humidity range: 10 ~ 90 % (non-condensing)
Certification and Compliance
EMI: FCC, CE, BSMI, RCM, VCCI
Safety: CB, BSMI, ETL
Other: RoHS, Energy Star, ErP
This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
(1) 2004/108/EC relating to electromagnetic compatibility (EMC),
(2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD),
(3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP)
[1] Optional LTE support
Shuttle provides the optional "Shuttle Accessory WWN03" which consists of an adapter card, two antennas plus 20 cm antenna cables. The WWN03 adapter card occupies the 2.5" drive bay, so that no more 2.5" SATA device can be installed. The 3G/LTE card must have M.2-3042 Key B format with MHF IV (I-PEX4) connectors for the antenna. In addition, it supports one Nano-SIM card (Mini and Micro format is not supported). The required 3G/LTE card and SIM card are not included in WWN03.
[2] How to convert DisplayPort into HDMI/DVI
The DisplayPort output can be converted to HDMI or DVI by an additional, passive adapter cable. For example:
DELOCK 82590: 1 m, DisplayPort (male, 20p) to HDMI-A (male, 19p)
DELOCK 82435: 5 m, DisplayPort (male, 20p) to DVI-D (male, 24p)
The integrated graphics automatically detects the connected display and puts out the appropriate electric signal - either through DisplayPort (without an adapter) or HDMI/DVI (with an adapter).
However, a monitor with a DisplayPort connector cannot be connected to the HDMI port with a simple, passive adapter.
[3] Power-on-after-power-fail
The BIOS setup provides a "Power-on-after-power-fail" function that can be found under "Power Management Configuration". As the name indicates, this function determines the PC's behaviour after power failure: (1) unconditional power-on, (2) restore former status or (3) keep system turned off. As a matter of the nature of this function, it may fail after short power failures. This is why the Shuttle XPC slim Barebone DL10J also comes with a hardware-based solution. By removing Jumper JP1 (on the mainboard behind the D-Sub/VGA port) the system will start unconditionally once power is supplied.
[4] Serial Ports
This PC features two serial RS232 ports with 9-pin D-Sub connectors on the back panel. The left COM port (COM1) can also be configured as RS422 and RS485 in the BIOS setup.
Pin 9 of the D-Sub COM-Port is a multi-functional signal. Based on the Jumper JP2 configuration on the mainboard, it can be configured as Ring Indicator (RI) or external power supply with a voltage level of either 5 V or 12 V. Each COM port can be configured separately. The maximum current is 500 mA per connector.
[5] TPM Function
This product features Firmware-TPM (fTPM) v2.0. Besides this, it is prepared for a hardware TPM chip which can be fitted by factory on request if required.
PRODUCTS
ACCESSOIRES:
ARTIKELNUMMER: SUNpc-EM317 uitbreidingsset voor WiFi en Bluetooth + 2 antennes.
Euro 679.00
|
|||||||||||||||||||||||||||||||
